Layered Skirt Tutorial

done_collage

I hope that you got a lot of use out of the reversible skirt tutorial!

This one is a variation on it so that any of those odd bids left at the end can be combined into a cute new skirt! I just love creating the casing at the top of the skirt between the layers so this skirt variation does the same thing!

As before the instructions are based off the simple skirt tutorial at MADE. If you haven’t visited her site you should, there’s a ton of great ideas there!

First assemble your supplies.

Supplies
Supplies

For this skirt you need the following:

One 6 in by 18 in long rectangle
One 4 to 5 in by 18 in long rectangle
One 10.5 in strip of 1/4 in elastic

The 6 by 18 rectangle will be the pop at the bottom and the shorter strip will be the top color. I used a 4 in strip for this so you can see more of the bottom fabric, but feel free to experiment! I used an 18 in as the width because it was the width of my fat quarter, but you could easily increase the width if you wanted a fuller skirt!

sewtube

First sew up the short end of each rectangle with a 1/4 seam allowance to create two tubes.

pressseams

Then because I usually forget earlier I finish the edges and then press them to the side (if you prefer to finish the edges earlier or have a serger please adjust to your preferences!). Since I was at the iron I pressed each seam to the side and turned up 1/4 in and then 1/4 again and pressed to create the hem.

sewhemshortinside

Then this is the confusing part (at least for me!). With right sides both facing up (towards you as you look at them) put the shorter piece inside the longer one aligned along the top. Then sew together with a 1/4 inch seam along the top. For this I sew along the right side.

trim

When done your skirt should look like this so trim along the top.

casing

Flip the longer piece inside, press and sew down 1/2 in to create the casing! Remember to stop about an inch or two before the starting point to insert the elastic!

insert_elastic

Insert elastic and sew ends together making sure it hasn’t twisted anywhere along the “waistband”.

Sorry, I must have forgotten to take a picture of this step, but finish the casing by sewing with a 1/2 seam along the opening that you left and enjoy!

done

Advertisements

Reversible Gathered Skirt

Image

This is my very first tutorial so I hope that everything is clear enough for everyone to follow!

I’ve been admiring the Pretty Plaid outfit from American Girl, but not the price tag so I wanted to try to recreate my own version.

However I wasn’t sure how until I saw this cute plaid at Wal-Mart and then the free pattern from Eden Ava (for signing up for their mailing list) that I knew that I could recreate it.

Since the top pattern is really wonderfully detailed (and takes almost no fabric) I’m going to let that speak for itself.  However, I would like to attempt to explain how I made the skirt in case anyone is interested!  I did the plaid skirt first to be sure it would work so I don’t have any pictures using that fabric.  No problem though, I just used that excuse to make a new skirt to go along with the tutorial!

This skirt pattern is loosely based on the instructions found at MADE on a simple skirt, however I adjusted it for my American Girl Doll and then inspired by the reversible top pattern decided to make it reversible!

So here it goes!

First gather your supplies:

  1. Two 6″ by 18″ rectangles (I used 18″ because that was the width of my fat quarter)
  2. One 10.5″ 1/4 inch elastic
  3. Trim as needed
  4. Sewing Stuff

Image

Once your supplies are assembled you first need to attach the trim.  For this skirt I only attached trim at the bottom.  I did it now because I wanted to keep the raw edges encased inside my skirt, but it did make the back look a little funky.  It worked beautifully when I attached it higher (sorry no in progress pics of that – it was my trial run!)

Image

Since I only added trim to the bottom the two skirts can share it, therefore I didn’t attach any to the other (blue) skirt.  For the plaid and flowered skirt at the top I attached the trim about an inch up from the bottom.

Next sew up each skirt at 1/4 in to create two tubes.

Image

Now you need to press the seams open and since I was at the iron I pressed the bottom (side with the rick rack on the green) up 1/4 inch.  Then put the two skirts together with right sides together.

Image

(Sorry forgot a picture of this!) But sew right at top of the skirt all the way around trying to make sure that the bottom of the skirt mostly matches.  Once you’re done then trim along the top.  If you forget it’s not a big deal, it just makes it a little easier to feed the elastic through later!

Image

Now flip the skirt right side out and press it so the wrong sides are together (sorry for all the pressing!) and sew 1/2 inch down from the top of the skirt stopping about 1 or 2 inches just before where you started.  This creates the casing between the two skirts.

(You can see in this picture how the trim “skips” right at the back seam because of the way I attached it)

Image

Once this is done you’ll have an opening between the two skirt layers which you can feed your elastic through.  Then make sure the elastic isn’t twisted and then sew it together.

Image

Finally put the skirt back on and finish the “waistband” by sewing across the gap you left to feed the elastic through.

Image

OK, almost done now, we just need to try to keep the two bottom edges together and top stitch right along the bottom of the skirt.

Image

And that’s it – you’re all done!  Feel free to repeat whenever your doll needs a new skirt (or the urge strikes)!

Image

Please let me know if anything isn’t clear, I’d love to get any feedback!

Continue reading